Coverall Fabric:

Disoposable coverall fabric  also call boilersuits, is a one-piece garment with full-length sleeves and legs like a jumpsuit, but usually less tight-fitting. Its main feature is that it has no gap between jacket and trousers or between lapels, and no loose jacket tails. It often has a long thin pocket down the outside of the right thigh to hold long tools. It usually has a front fastening extending the whole length of the front of the body up to the throat, with no lapels. It may be fastened with buttons, a zip, velcro, or snap fasteners. Boiler suits with an attached hood are available.

Work wear coverall fabric  and uniforms using in the catering, construction, medical, education, etc. for the coverall material mainly use is cotton, polyester or function flame resistant fabric. all these material with different weight, the quality will better if the fabric weight is high. different type fabric have different feature.

disposable coverall fabric is essential for frontline healthcare workers to control and prevent infection .Protective

clothing is designed to cover the entire body , thereby providing comprehensive protection against exposure

to the virus by creating a barrier to reduce contact and droplet exposure.

Due to the COVID-19 pandemic ,personal protective equipment(PPE) has become a global demand; therefore,

the demand on the supply chain especially for raw materials is higher. The raw fabrics used to produce PPE

must be suitable so that the final protective garment product can provide the two most important functions:

penetration resistance and comfort .The purpose of this article is to explore the materials required for protective

clothing.

The specifications of the protective clothing are :

meets quality requirments (fabric properties of protective clothing)

Impermeable to blood and body fluids

Antiviral

Comfortable to wear

Disposable or reusable

Common protective clothing materials

Most disposable protective clothing is made of non-woven synthetic fibers.As the level of protection increase

strength, reduce permeability and potentially make them flame retardant.

Coating/lamination

coatings or laminates can provide other functions such as fluid resistance, antimicrobial properties ,antiviral

properties,etc.

Protective clothing is usually made from the following

synthetic fibers:

Polypropylene(PP)

Polyester(PET)

Polyethylene(PE)

single -tier architecture

The most basic suits will be made from a single layer of spunbond polypropylene and are breathable

and relatively comfortable.It is typically used by workers in spray booths or as a basic barrier for harmless

cleaning operations in most dry environments.

SMS Spunbond Meltblown Spunbond Construction another popular material is known by its acronym SMS

This is two layers of identical spunbond polypropylene with a layer of meltblown polypropylene in the middle

The composition is still comfortably breathable but is tear and puncture resistant and has enhan liquid resistance .Less comfortable than microporous breathable membrance.

Polyethylene coated Polypropylene(PPSB+PE) fabrics for this construction, spunbond polypropylne is

coated with a layer of water-impermeable polyethylene . The material has excellent waterproof and impermeable properties. The suit is widely used in fluid resistant areas to protect the wearer from

liquid chemicals or biological hazrds.

PPSB+PE is deal for providing protection against fluids

Microporous breathable membrane

Breathable membranes are thin films, microporous or monolithic membranes that are impermeable

to liquids(water/blood)but permeable to gases (water vapor).Rising penetration of hygiene products

such as baby diapers,sanitary napkins , and adult incontinence products in developing countries,

while increasing consumption of advanced hygiene products in developed countries is expected

to boost breathable membranes globally.The high cost of breathable films compared to conventional

film is a major restraining factor for the global breathable films market.Microporous breathable

membranes are ideal for providing excellent comfort and protection when used in PPEand coveralls,

By combining microporous breathable membranes with other materials, a new type of PPE fabric

can be made.

(Microporpus breathable membranes offer higher percent heat loss, chemical protection, but cost more.

Combined with other materials, new PPE materials can be made.)

Custom layer

If you want to increase the protection level of work clothes, a common method is to increase the prtective

layer and polymer of the protective clothing.Higher layers of protection generally mean reduced comfort ;

however, if certain environmental hazrds require greater isolation from chemical or toxic vapors, a higher

level of protective clothing may be required.

Material requirements for protective clothing fabrics

Fabrics and seams are important to any workwear and they are closely related to the protection rating

of the workwear .Considering common routes of contamination from COVID19, the key tests in EN 14126

are listed below:

ISO 16604 :Resistance to penetration of contaminared liauids under pressure (close contact with a patient

may result in direct contact with water droplets from coughing or sneezing)

EN 14126 Annex A: Anti-infectious penetration due to mechanical contact with substances containing

contaminated liquids (contact with bed rails or door handles)

ISO 22611: Protection against penetration of contaminated liquid aerosols (subject to Contaminated droplets

from infectious aerosols through coughing or sneezing)

ISO 22612 :Protection against penetration of contaminated solid particles (contact with contaminated dust )

Name	Specification
Weight	10gsm ~ 100gsm
Width	80mm ~ 2000mm
Color	White, Green, Blue, Yellow, Orange. Desire color and printing design are also acceptable by demand.
Print	Up to 4 colors printed will allow to imitate multiple colorful print.
Grade	Base material for Hygienic, Industrial, Agricultural, House wrapping application.

Our Certifications

Quality Control

FAQ

Product information

Q: What is the width?

A: We can supply width from min. 80mm to max. 2050mm.

Q: How about the film color?

A: The regular colors are White, Green and Blue. Other colors are also available.

Q: How about the film printing?

A: We have excellent 4 colors (Red/Blue/Yellow/Black) printing machine which print photo-like design on the film.

Q: Is customized available?

A: 1) Film performance: Yes, we can follow customer's demand to change condition on resin or machine to meet customer required.

2) Printing customizable: Yes, we can follow customer's design to print on the film.

3) Packaging details: Yes, we can follow customer's demand for different size on box and pallet.

Other information

Q: Do you offer distributorship?

A: Yes, partnership are most welcome, but it depends on what products and area. Please contact us for further information.

Q: Is Consultation available ?

A: Consultant always our pleasure if any require regarding our products, materials from customer, we will happy to help.

Q: I don't have clear product specification. I just have a piece of sample. Can I get further information from you?

A: Please send us the sample (sample size over A4 ) and tell us your requirement. We will analyze the sample after we received it. We will share the report with you and suggest you the most similar or even better item for your further.

Q: I had bad experience with other supplier, how can I make sure you will make it right?

A: Long business relationship should base on a mutual trust by each both parties, we always promise to provide our best service to any of our customer.

http://www.taiwanfabric.com/